入模温度 molding temperature英语短句例句大全

入模温度,molding temperature

1)molding temperature入模温度

1.In this paper, the integration of foundation pile conduction, frozen soil, air temperature, concrete hydrate heat, concretemolding temperature is considered to establish a numerical simulation.考虑基桩传热、地基冻土、大气温度变化、混凝土中水泥水化热、混凝土入模温度变化及其相互作用,建立温度场数值分析模型。

2.In order to control the concretemolding temperature, one or more measures(pre-cold-ing of cement, water washing of aggregate, batching with iced water or ice pieces), should be adopted according to different air temperature.本文结合工程实例介绍了预拌加冰混凝土的温度计算公式和理论用冰量的计算公式,提出了在不同气温条件下应分别采取一种或多种温控措施(水泥预冷却、砂石冲洗、加冰水或碎冰搅拌等)以控制混凝土的入模温度,并推导得出了预拌加冰混凝土的最低入模温度极限值。

2)pumping"s temperature入模温度

3)conditioning temperature制粒入模温度

1.crossbred piglets were randomly assigned to particle size andconditioning temperature of mash.(2 )饲料粉碎粒度下降 ,制粒入模温度提高 ,使颗粒饲料淀粉糊化度提高 ,粉化率下降。

4)Inlet Temperature入口温度

1.Three-dimensional Finite Element Model (FEM) Analysis of the Roller"s Shape with an UnevenInlet Temperature Field in Continuous Roll-casting Process;非均匀入口温度场下铸轧辊辊型的三维有限元仿真

2.Propellant inlet temperature control for cryogenic rocket engine tests低温发动机试验推进剂入口温度控制

3.The influence of fluid component content and inlet temperature on the flow in gas condensate pipeline-riser system流体组分含量及入口温度对天然气凝析液输送管道立管系统流体流动特性的影响

英文短句/例句

1.Propellant inlet temperature control for cryogenic rocket engine tests低温发动机试验推进剂入口温度控制

2.The Investigation of Influence to Outside Wall Temperature in Pipe When Inlet Temperature Changes;圆管入口温度突变影响管外壁温度的研究

3.Modeling and Optimization for the Temperature of Converter Inlet on Metallurgical Acid Plant烟气制酸转化器入口温度建模与优化设定

4.The influence of fluid component content and inlet temperature on the flow in gas condensate pipeline-riser system流体组分含量及入口温度对天然气凝析液输送管道立管系统流体流动特性的影响

5.If Outlet is COLDER than Inlet, temperature differential is minus (-).如果出口温度比入口低，温度差是减(-)

6.The axillary temperature is about1 degree Fahrenheit less than an oral temperature.腋窝温度比口腔温度大约低1华氏度。

7.bedded temperature detector嵌入式测温计;嵌入式温度计;埋入式温度计;埋置式温度探测器

8.This time, he managed to climb into the mouth of Kituro so that he could take photographs and measure temperatures.这次,他设法爬入基图罗火山口,以便拍照和测量温度。

9.An Automatic Voltage Control Method Based on Tracking ESP Inlet Gas Temperature跟踪电除尘器入口烟气温度的自动电压控制方法

10.stabilization of export receipts system“稳定出口收入”制度

11.Influence of Feeding Angle on Temperature Field in Molten Pool不同水口角度对熔池内温度场的影响

12.A folding mechanism plaits the fabric onto the roller bed.织物经一段自由布段后从汽封口进入蒸箱，并被迅速加热到反应温度。

13.Replace the insulation making sure that the controls are well covered and that the plastic terminal shield has not been displaced; then replace the access panel.把绝缘层重新放在原先的位置,确保温度控制器被绝缘层完全包裹,接着把入口面板重新盖上。

14."Remove the access panels or front panel on table tops, fold the insulation outward away from the controls."将热水器上的入口面板拆卸下来,把温度控制器的外部绝缘层拿下来。

15.Thermostats are factory set and wired in accordance with the wiring diagram fastened to the inside of the top access panel.温度控制装置在工厂就预先设置,并且按照电路图所示进行布线,固定在热水器顶部面板入口内。

16.The adiabatic heating induces the temperature of fracture surface layer to be higher than the liquidus temperature too.计算表明,断口表面层绝热升温温度依然高于液相线温度.

17.The outlet pipe of the VOD can reach temperatures up to120℃.VOD的出口温度能达到120℃温，所以必须预防接触。

18.A rectal temperature reading is generally 1 degree Fahrenheit higher than an oral reading.直肠温度的读数一般大于口腔温度1华氏度左右。

入模温度 molding temperature英语短句 例句大全

入模温度 molding temperature英语短句例句大全