双管板换热器,double tube-sheet heat exchanger
1)double tube-sheet heat exchanger双管板换热器
1.Study on the design thickness of tubesheet fordouble tube-sheet heat exchanger双管板换热器管板设计厚度探讨
英文短句/例句
1.R&D and Application of Dual-tube & Dual-tube Sheet Heat Exchanger双冷却管双管板换热器的研发及其应用
2.Surfacing on Duplex Stainless Steel Tube-plate of Heat Exchanger and Welding on Tube-port of Heat Exchanging Tube换热器管板双相不锈钢堆焊及管板与换热管管头焊接
3.The type selection of Shell-And-Tube Heat Exchanger and Plate Heat Exchanger管壳式换热器与板式换热器选型参考
4.fixed tube sheet type heat exchanger固定管板式热交换器
5.bare-tube coil heat exchanger光板盘管式热交换器
6.Research on Welding Process of Duplex Stainless Steel Tube to Tubesheet Made of 316L双相不锈钢换热管与316L管板焊接工艺
7.The Active Connection Technology about Heat Exchange Tube and Tube-sheet管壳式换热器中换热管与管板的活性连接技术
mon Problems in Welding Joint of Tubesheet and Tube for Heat Exchanger换热器管板与换热管焊接常见质量问题的防止
9.Quality Control of the Fillet Weld in the Tube and Tube Sheet of Heat Exchanger换热器管-管板角焊缝焊接质量的控制
10.Abstract: Plate-shell heat exchanger (PSHE) is new equipment of combining the advantage of shell and tube heat exchanger and plate heat exchanger.文摘:板壳式换热器是集板式换热器和管壳式换热器优点于一身的新型换热设备。
11.Finite Element Analysis of the Tubesheet in a Large Fixedtube Sheet Heat Exchanger;大型固定管板式换热器管板的有限元分析
12.Finite Element Analysis of Tubesheet in Fixed Tubesheet Heat Exchanger固定管板式换热器管板强度的有限元分析
13.Tube-Sheet Parametric Design Based on SolidWorksSolidWorks中换热器管板三维参数化设计
14.Finite Element Analysis on Stress of Fixedtube Sheet Heat Exchanger固定管板式换热器应力的有限元分析
15.Stress Analysis Calculation of Tube-sheet for EA-304 Heat ExchangerEA-304非对称换热器管板应力分析计算
16.Preventive measure and the origin of the crack which the stainless steel heat exchanger tube plate染机换热器管板裂纹成因分析及控制
17.Ablation&Corrosion to Carbon Heat Exchange Tubes and Tubesheet in HP Heater高压加热器碳钢换热管及管板的冲蚀和腐蚀
18.Tube and Tubesheet Design Methods for Tubular Heat Exchanger with a Central Pipe;带中心管的管壳式换热器管板与换热管设计方法研究
相关短句/例句
tubular sheet heat exchanger管板换热器
1.Failure analysis and improvement of ultrathintubular sheet heat exchanger of Dongfeng 4C;东风4C超薄管板换热器的失效分析与改进
3)tube-sheet heat exchanger管板式换热器
1.The method is suggested to calculate wall temperatures and temperature differential stresses by integral (average) temperatures on pass of cold and hot fluid to replace arithmetic average inlet-and-outlet temperatures of fluid for single pass fixedtube-sheet heat exchanger.本文对单程固定管板式换热器,提出了采用冷、热流体的沿程积分平均温度代替算术平均温度来计算壁温和温差应力的方法,并从温差应力和内压应力共同作用的情况下考虑膨胀节的设置条件。
4)thin tubeplate薄管板换热器
5)Fixed tubesheet heat exchanger固定管板换热器
6)wrapped type heart exchanger板管式换热器
延伸阅读
固定管板换热器分子式：CAS号：性质：将一束管两端穿过端板并固定在端板上，并将此放入壳体内，两端管板和壳体固定成一体，具有结构简单和成本低的优点。但壳程清洗和检修困难，因此，要求壳方流体必须是清洁且不易结垢的物料。当两流体温度差较大时，应考虑热补偿。图示为（图暂缺）具有补偿圈(或称膨胀节)的固定管板换热器。当外壳和管束热膨胀不同时，补偿圈发生弹性变形以适应外壳和管束不同的热膨胀程度。这种补偿方法简单，但不宜应用在两流体温差过大(应不大于70℃)和壳程流体压强过高(一般不高于600kPa)的场合。
