导向弯曲试验,guide bending test
1)guide bending test导向弯曲试验
1.The purpose of weldguide bending test is to detect plasticity of welding joint,welding process and surface defects of materials.焊缝导向弯曲试验的目的是检查焊接接头的完好性和塑性以及材料的焊接工艺和表面缺陷。
2)root bendtest,reverse bend test反向弯曲试验
3)buckling test纵向弯曲试验
4)transverse bending testing machine横向弯曲试验机
5)single bend test单向弯曲试验
英文短句/例句
1.Figure 3, 4 shows a flat piece of metal that has been through an angle of 180. Sheet metal may be given a single bend test图3．4表示一片金属扁试样被弯曲180°可以对薄板金属进行单向弯曲试验，
2.Test methods for bare wires--Bend test--Single bend testGB/T4909.6-1985裸电线试验方法弯曲试验单向弯曲
3.alternative wrap around guided-bend test交变缠绕定向弯曲试验
4.Test method for flexural properties of unidirectional fiber reinforced plasticsGB/T3356-1999单向纤维增强塑料弯曲性能试验方法
5.Research on Bending Rotation Test of Rotation Shaft in Point the Bit Rotary Steerable System指向式旋转导向系统旋转轴弯曲旋转试验研究
6.fine ceramics(advanced ceramics, advanced technical ceramics)-test method for flexural strength of monolithic ceramics at elevated temperature细陶瓷-单块陶瓷高温弯曲强度试验方法
7.flexing ozone weather testing chamber臭氧腐蚀弯曲试验箱
8.testing method for flexing endurance of light leathers and their surface finishes皮革耐弯曲性试验方法
9.testing method for flexural creep of plastics塑料弯曲蠕变试验法
10.rotary bending tester旋转弯曲疲劳试验机
11.rotating bending fatigue machine回转弯曲疲劳试验机
12.reversed bending fatigue machine反复弯曲疲劳试验机
13.Test methods for bare wires--Bend test--Reverse bend testGB/T4909.5-1985裸电线试验方法弯曲试验反复弯曲
14.With data obtained from low temperature bending and bending creep test, a simple calculation method is given for calculating rupture energy.应用低温弯曲和弯曲蠕变试验所得数据,给出了破坏能的简单计算方法。
15.Methods of test for enamelled wires--Mandrel winding test for rectangular wiresGB/T4074.7-1983漆包线试验方法扁线弯曲试验
16.fine ceramics(advanced ceramics, advanced technical ceramics)-determination of fracture toughness of monolithic ceramics at room temperature by the surface crack in flexure(scf) method细陶瓷-单块陶瓷常温断裂韧度试验方法-弯曲表面龟裂法
17.Plastics--Determination of flexural properties by use of small specimensGB/T16419-1996塑料弯曲性能小试样试验方法
18.INFLUENCE OF HOLE POSITION ON BENDING RIGIDITY OF UD-LAMINATE穿孔位置对单向层板弯曲刚度的影响
相关短句/例句
root bendtest,reverse bend test反向弯曲试验
3)buckling test纵向弯曲试验
4)transverse bending testing machine横向弯曲试验机
5)single bend test单向弯曲试验
6)cross-bend test横向弯曲试验
延伸阅读
导向引导的方向：新闻工作要坚持正确的舆论导向。
