螺纹牙,Screw-threads
1)Screw-threads螺纹牙
1.Mathematical Description of Distributing Curve of Force inScrew-threads of Micron Wood Fiber Molded Products微米木纤维模压制品螺纹牙受力分布曲线的数学描述
英文短句/例句
1.minimum number of pipe threads for connections管螺纹连接的最少螺纹牙数
2.basic crest truncation基准螺纹牙顶切除高度
3.Miniature screw threads-ProfilesGB/T15054.1-1994小螺纹牙型
4.Metric trapezoidal screw threads-ProfileGB/T5796.1-1986梯形螺纹牙型
5.Buttress threads with 3 and 30 degrees flank angle-ProfilesGB/T13576.1-1992锯齿形(3°、30°)螺纹牙型
6.A study of the surface crack at thread root of tool joint pins by the aid of finite element method.石油钻杆公接头螺纹牙根部表面裂纹有限元计算
7.55 inch thread flat tangential die55°英制螺纹切线平板牙
8.all screw threads are according to aNSI B-1.1 coarse thread.所有螺栓的螺纹都符合aNSI B-1.1粗牙螺纹标准。
9.Hexagon head bolts-Fine pitch thread-Full thread-Product grades A and BGB/T5786-1986六角头螺栓--细牙--全螺纹--A和B级
10.Screw thread shanks for thread forming screw--Metric coarse thread seriesGB/T6559-1986自攻锁紧螺钉的螺杆粗牙普通螺纹系列
11.55 inch thread tagential die for taper pipe55°英制圆锥管螺纹切线平板牙
12.left hand thread左螺纹,倒牙(逆时针方向旋进)
13.General purpose screw threads--Basic concepts and symbols for tooth shapes and tolerance zoneGB/T192-1981普通螺纹基本牙型
14.Length insufficience of reinforced bar tooth and settlement method螺纹钢牙筋长度不足的原因及解决办法
15.Mechanical properties of fasteners--Thread forming screws--Metric coarse thread seriesGB/T3098.7-1986紧固件机械性能自攻锁紧螺钉粗牙普通螺纹系列
16.The Clinical Effection Evaluation Of Applying CDIC conical Spiral Implant In The Humble Knifing-posterior Of The MandibularCDIC锥状螺纹种植体在下后牙区菲薄型牙槽骨的临床应用评价
17.An apparatus for holding the dies that cut threads on screws, bolts, pipes, or rods.板牙铰手一种用来夹持切削螺钉、螺柱、钢管或拉杆上螺纹的螺丝模的装置
18.boxpin connection阴螺纹-阳螺纹连接
相关短句/例句
Coarse thread粗牙螺纹
3)Fine pitch thread细牙螺纹
4)tetragonal thread方牙螺纹
5)root of thread螺纹牙底
6)thread profile螺纹牙形
延伸阅读
攻螺纹、套螺纹及其注意事项常用的在角螺纹工件,其螺纹除采用机械加工外,还可以用钳加工方法中的攻螺纹和套螺纹来获得。攻螺纹(亦称攻丝)是用丝锥在工件内圆柱面上加工出内螺纹;套螺纹(或称套丝、套扣)是用板牙在圆柱杆上加工外螺纹。 一、攻螺纹 1.丝锥及铰扛 (1)丝锥 丝锥是用来加工较小直径内螺纹的成形刀具,一般选用合金工具钢9SiGr制成,并经热处理制成。通常M6~M24的丝锥一套为两支,称头锥、二锥;M6以下及M24以上一套有三支、即头锥、二锥和三锥。 每个丝锥都有工作部分和柄部组成。工作部分是由切削部分和校准部分组成。轴向有几条(一般是三条或四条)容屑槽,相应地形成几瓣刀刃(切削刃)和前角。切削部分(即不完整的牙齿部分)是切削螺纹的重要部分,常磨成圆锥形,以便使切削负荷分配在几个刀齿上。头锥的锥角小些,有5~7个牙;二锥的锥角大些,有3~4个牙。校准部分具有完整的牙齿,用于修光螺纹和引导丝锥沿轴向运动。柄部有方头,其作用是与铰扛相配合并传递扭矩。 (2)铰扛 铰扛是用来夹持丝锥的工具,常用的是可调式铰扛。旋转手柄即可调节方孔的大小,以便夹持不同尺寸的丝锥。铰扛长度应根据丝锥尺寸大小进行选择,以便控制攻螺纹时的扭矩,防止丝锥因施力不当而扭断。 2.攻螺纹前钻底孔直径和深度的确定以及孔口的倒角 (1)底孔直径的确定